Posted in

What O-Rings are used in aerospace applications?

When I first started out in the o-ring supply business, I had no idea how critical these small, circular pieces of rubber would be to the aerospace industry. Most people see an o-ring as a simple seal—something that keeps water out of a garden hose or oil in a car engine. But in aerospace, an o-ring isn’t just a component; it’s a fail-safe that can mean the difference between a successful mission and a catastrophic disaster. Over the past 12 years, I’ve supplied o-rings to dozens of aerospace contractors, and every interaction has taught me how tailored these parts need to be for the extreme conditions of flight, space, and atmospheric re-entry. O-Ring

Let’s start with the basics: aerospace o-rings are designed to seal against two types of threats—pressure differentials and environmental extremes. On a commercial airliner, for example, the cabin is pressurized to around 8,000 feet even when the plane is flying at 36,000 feet. That creates a pressure gap between the inside of the fuselage and the outside, and o-rings line every access panel, hydraulic line, and fuel tank connection to prevent decompression. For a satellite in low Earth orbit, the threats are even starker: extreme temperature swings (from -150°C in the shadow of Earth to 120°C in direct sunlight), vacuum conditions that can cause rubber to outgas, and tiny micrometeoroids that could puncture a seal. That’s why not all o-rings work for aerospace applications—we have to pick the right material, size, and durability for each specific use case.

One of the most common aerospace uses I see is in hydraulic systems. Commercial jets rely on hydraulic pressure to move their landing gear, flaps, and ailerons. These systems operate at pressures up to 3,000 psi, and the o-rings that seal hydraulic cylinders have to hold up not just to that pressure, but to the fluid itself—usually a phosphate ester-based hydraulic fluid that can break down standard rubber. For this, I primarily supply o-rings made from Buna-N nitrile rubber or EPDM, but wait—Buna-N isn’t right for every hydraulic system. Older regional jets often use Buna-N because it’s resistant to standard hydraulic fluid and can handle temperatures from -40°C to 120°C, while newer wide-body planes that fly at higher altitudes (where temperatures can drop even lower) use a fluorocarbon (Viton) o-ring, which has a wider temperature range (-20°C to 200°C) and is more resistant to both heat and chemical breakdown. Last year, I fulfilled a bulk order for a major aerospace component manufacturer that builds hydraulic actuators for Boeing’s 787 Dreamliner; they specifically asked for Viton o-rings because the Dreamliner’s hydraulic systems run hotter than older models, and the seals need to last the lifespan of the plane, not just a few years.

Another area where aerospace o-rings are non-negotiable is in fuel systems. Jet fuel is a harsh substance, and fuel tanks on aircraft are designed to hold fuel while also resisting ignition—even in a lightning strike. O-rings in fuel tank connections have to be resistant to jet fuel (both kerosene-based and alternative sustainable aviation fuel blends) and also meet strict fire-safety standards, meaning they can’t release toxic fumes or burn easily. For these applications, many of my clients turn to silicone o-rings? No, wait—silicone isn’t resistant to jet fuel. Silicone works for things like cabin air systems, but fuel systems require either EPDM or fluorosilicone. Fluorosilicone is a middle ground: it’s got the heat resistance of silicone (up to 200°C) but is resistant to hydrocarbon fuels, which standard silicone isn’t. I once had a client come to me with a problem after a test flight where their fuel line o-rings were swelling up; they’d used regular silicone, and it reacted with the alternative aviation fuel they were testing. We swapped them for fluorosilicone o-rings, and the issue was gone immediately. That’s the kind of problem that makes aerospace o-ring work so important—one wrong material, and a whole test program can be delayed.

Then there’s space exploration, which is a whole different ballgame. When I supply o-rings for satellites, I have to comply with NASA’s outgassing standards (ASTM E595), which measure how much volatile organic compounds (VOCs) a material releases in a vacuum. If an o-ring outgasses, those compounds can condense on a satellite’s optical sensors, solar panels, or camera lenses, ruining their performance. Most satellite manufacturers prefer o-rings made from perfluoroelastomers (FFKM), which are the most resistant to outgassing, extreme temperatures, and chemicals. FFKM o-rings can handle temperatures from -50°C to 320°C, which makes them perfect for satellites that spend years in orbit, exposed to vacuum and solar radiation. A couple of years ago, I worked with a small satellite startup that was building a CubeSat for Earth observation; they needed o-rings for their propulsion system, which would use small amounts of monopropellant. Monopropellant is highly reactive, so the o-rings had to not only resist the propellant but also meet NASA’s outgassing rules. We supplied custom-sized FFKM o-rings, and they told me later that the seals performed flawlessly during the six-month mission. That’s the kind of work that makes me proud to be an o-ring supplier—we’re contributing to technology that helps monitor climate change, track wildfires, and connect remote parts of the world.

I can’t talk about aerospace o-rings without mentioning the 1986 Space Shuttle Challenger disaster, even though it’s a tragedy that changed everything for the industry. The Challenger’s solid rocket booster o-rings failed because they couldn’t handle the cold temperatures on launch day—below freezing, which made the rubber less flexible. That disaster led to major changes in how aerospace o-rings are tested and specified. Now, every o-ring for a space application has to go through rigorous temperature testing, pressure testing, and thermal cycling to make sure it can handle even the most extreme conditions. For ground test equipment, o-rings have to withstand repeated temperature changes—from room temperature in the lab to -100°C in a test chamber, then back up again. I supply a lot of o-rings to test facilities, and each one is tested in our warehouse before shipment—we don’t cut corners on quality, because I know that every seal is part of a larger system that can’t afford to fail.

Another often-overlooked aerospace application is in environmental control systems (ECS), which regulate the temperature and air quality inside aircraft cabins. O-rings in ECS components have to seal against conditioned air, which can be at high pressure or very low pressure, and also resist moisture and temperature swings. Here, EPDM o-rings are popular because they’re flexible, resistant to ozone and moisture, and can handle temperatures from -50°C to 150°C. I also supply silicone o-rings for cabin air ducts, since they’re odorless and don’t release any harmful chemicals into the air—an important point for passenger comfort, especially on long-haul flights. A few months ago, I got a call from a regional jet maintenance company that was having trouble with leaks in their ECS ducts; the original o-rings had hardened over time, allowing moist air to seep out. We supplied a new batch of EPDM o-rings with a higher durometer (hardness) that was better suited for older duct systems, and the leaks were fixed. That’s another part of the job—working with clients to find the right o-ring when a replacement part isn’t exactly what it needs to be.

Of course, there are challenges specific to being an aerospace o-ring supplier. Aerospace projects often require custom sizes—standard o-rings just don’t work for many applications, because components are unique to each aircraft or satellite. I keep a small inventory of common sizes, but 70% of my aerospace orders are custom-machined. That means working with engineers to get exact dimensions, tolerances, and material specifications, and then testing each custom o-ring to make sure it meets aerospace standards. Lead times are also tight—many aerospace clients need parts in 2-3 weeks, not the standard 4-6 weeks for commercial o-rings. I’ve invested in small, precision machining equipment to handle custom orders quickly, and I’ve built relationships with material suppliers that can deliver aerospace-grade elastomers fast. No one wants to wait for an o-ring when a plane is grounded or a satellite is waiting to launch.

I also have to make sure all my o-rings meet regulatory standards, like those set by the Federal Aviation Administration (FAA) for commercial aircraft and NASA for space systems. Every batch of o-rings I supply comes with a certificate of conformance, proving that it’s been tested and meets the required specifications. For some programs, I even have to provide traceability documents, showing exactly where the elastomer material came from, when it was molded, and who handled it. It’s a lot of paperwork, but it’s necessary—aircraft and satellites can’t use parts that don’t meet strict quality and safety standards.

Over the years, I’ve learned that aerospace o-ring work isn’t just about selling a circular rubber seal. It’s about understanding the application, the conditions the seal will face, and the regulatory requirements that govern it. Whether it’s a commercial jet’s hydraulic system, a satellite’s propulsion system, or a test chamber for a new rocket engine, every o-ring has a job to do, and if it fails, the consequences can be serious. That’s why I don’t just ship o-rings— I work with my clients to make sure they get the right part, tested and ready to perform when it matters most.

If you’re an aerospace engineer, maintenance manager, or program coordinator looking for reliable, high-performance o-rings for your next project, I’m here to help. We can discuss your specific application, review material specifications, and provide custom or standard o-rings that meet your needs and regulatory requirements. Don’t take chances with critical seals—let’s connect to find the right solution for your aerospace project.

Cogged V Belt References
NASA. (1995). ASTM E595: Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment.
Federal Aviation Administration. (2020). Aircraft Materials and Processes: Elastomer Seal Requirements for Flight Critical Systems.
National Aeronautics and Space Administration. (1988). Report on the Space Shuttle Challenger Accident.
Society of Automotive Engineers. (2018). AS4716: O-Rings, Synthetic Rubber, for Aerospace Applications.


Xingtai Boshuo Auto Technology Co., Ltd.
Xingtai Boshuo Auto Technology Co., Ltd. is one of the most professional o-ring manufacturers and suppliers in China, featured by quality products and low price. Please rest assured to wholesale bulk customized o-ring made in China here from our factory. Welcome to contact us for pricelist and free sample.
Address: No. 58 Quannan East Street, Xiangdu District, Xingtai City, Hebei Province
E-mail: sherry1@bs-belt.com
WebSite: https://www.bsbelts.com/